My mother said it beeped trouble, I replaced the battery and it shows not ready. I did not read I had to reset anything. Last battery replacement just worked. Any ideas?
Dave is correct, and the extra buttons wont work. One of them was to record a message so when loved ones wouls disarm, it would spit out the message. I am using 2 original aegis consoles with no issues.
I have an hai console that 80% of the buttons not working . Is there something that breaks inside that gets out of alighnment? Dad was very heavy fingered in his late 90s and both console’s keys are not registering to pushes.
Thanks for your detailed reply. I think I ruled out the omniLT as the source of the problem. The details that led me to this are quite lengthy so I will not bore you with the details, but it was a head scratcher for quite some time. I was at my wits end when I made the OP, but sometimes you have...
Hi, having an issue with the omnipro picking up the landline (Bell Canada) , thus hanging up my voice call. This just started intermitantly over the last month. It usually will happen within a min of answering the phone.
anyone have an idea where to start troubleshooting?. Would this have...
I actually detached the zone after replacing the wired sensor .making no change. To eliminate any wire issues I placed a 1k across the zone and still read low 130s (low enough to make the zone not ready. Did a system reboot with no change so I think it has to be the board.
HM
I have a 16 zone , 16 Output expansion board PART NUMBER
17A00-1
One zone keeps going not ready, I replaced the sensor never thinking it was the board, it seemed to fix the issue, but zone one went not ready again. The zone readout is lower than the rest when secure, around 143 vs 148 for all...
Hi, I have an HAI Omnipro console keypad inwhich the number three button and off button are non-responsive.
Has anyone successfully disassembled and repaired an issue like the one I am dealing with?. WThe off button can be activated with significant pressure, but the number three button will...
I have been using intella villa for my omniproll for a couple of years waiting for some finalization of space. I had an uneasy feeling about the developer. I guess all the beta guys are under nda so we will never find out what happened.
Can someone suggest an ios app I can buy. I see one called...
Well, for anyone wanting to use an old rc-80 omnistat to control a fireplace, the above works, just connect the data as a normal connection to the omni panel, run 24vac from the panel to power the thermostat to the R and C screws, then run a pair from the W and C screws to a 24vac relay. When...
What I think I will do is find out if 24 vac comes out of the w terminal when heat is called for. Would 24 vac appear during heating on the w and c terminals? I made a bridge rectifier to convert the ac to dc as I only have a 24dc relay on hand. If I do it this way it will isolate the panel...
I have a omnistat rc-2000 HAI thermostat to control my hvac. Apparently the omniproll knows when this thermostat calls for heat, but I assume the older RC-80 does not act the same way.
I thought I would use the old thermostat to control the fireplace with an automation block that says "when the...
There is a feature that will check to see if you actually leave. It is called "unvacated Premises" under "Arming" This may be your issue if it is set to Yes.
If you want to stay in the house you could choose night delay and that should give your wife the same delay to get in as Away does. I...
I have been sitting back and watching these threads now for over a year. I almost advised clents to purchase this software also, but my instinct told me to wait. Every month that goes by I feel the disappointment of those early adopters that chose to support Space. I can sort of see the...
Can anyone paste in here the changelog for firmware since ver 3.0 for the omnipro 2. In my absence I guess HAI has been sold to Leviton???. Anyways, their site just runs me in circles and provides no useful information unless of course I am a perspective buyer. I am looking at doing some...
Thanks Cornutt,
Using them in that way didn't dawn on me. Thanks so much for your input. I think I better hold off a bit longer to rewrite my code till I rethink the power of this setting. I've googled this topic quite a bit but there are very little real world examples and I can see now...
I have an HAI Omnipro2 with 3.1 firmware. I am finally getting time to rewrite and streamline, organize and change my programming. All 975 lines of it.
I sort of understand the concept of "user settings", but don't fully comprehend how implementing these will benefit me as the person with...
Hi Jeff,
Unfortunately Ontario Smart Meter program is not Zigbee compatible. The invented some proprietary system that was very cost effective for them, so much so that many other communities are adopting it.
The $25 reduction for joining their voluntary program is not a $25 monthly...
Do you have the HAI Omni controller to go with it? If so , I just did one using the outputs on the Omnipro2 and it worked out great.
I used two of the outputs. Once the omnipro decides that the hvac is in heating and a call for humidity is required, it closes one relay to the water solenoid. I...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.