Search results

It has been a while since I did this, but my recollection of the steps are    1. Install Growl on Mac 2. Install Prowl on iPhone   Follow these instructions:  https://www.prowlapp.com/installation.php Click on the Applications tab/HaikuHelper in Growl preferences to make sure it is setup how you...

Thanks for the explanations.

The scenario was that my fire alarm went off when I wasnt home. Received a notification on my phone. I checked my cameras in the house and everything looked ok. Cleared the alarm with Haiku via entering code. Alarm company called and I told them to cancel fire dept response. Just still...

This may be more of an Omni question than a Haiku question, but If I clear a fire alarm remotely via Haiku and there is still smoke causing the fire alarm will the fire alarm activate again or is there a timeout that prevents it from re-activating for a certain timeframe.

Unfortunately, that didn't help...and now my Growl notification setup isn't working.  I had installed Growl on my Mac and Pushover on my iPhone which was working in place of the Haiku notifications.  It was working this morning and now it isn't.  I can get notifications via email.   EDIT...

My notifications seemed to have stop working again. I made the changes as suggested in the thread at the end of February and was able to receive notifications over the last several weeks. Anyone else having trouble again?

I have an OmniLTe panel.  The LTe has 32 units available for allocation and I have already allocated 22 using HLC for "House Code Format"  I have a Zigbee lock that works great with the panel.   I just purchased a  Zigbee plug-in load module.  It appears that to have the panel control it, I have...

Well, AT&T came out today.  I explained the situation and asked them if we could try a new router.  Tech said sure.  Problem solved.   The new gateway is a Pace 5268AC.  It allows entry of a static IP to create a port forward regardless if the device is detected by the gateway.   Thank you for...

I just tried this, but it didn't seem to work (that is, if I followed your directions correctly).  I believe the issue is that the UVerse router configuration allows you to assign the port forwarding to a specific device, by MAC  address, not by IP address.   When I changed my laptop to the...

Thanks for the suggestion.  Unfortunately, I haven't found a way to do it with the UVerse router.

I have an OmniLTe (4.0b) connected to an ATT UVerse NVR589 router.  This setup has been working without a problem for almost two years.  This week we had some issues with our ATT service and I was instructed by ATT to reboot my router by.  I can't remember if I have ever done this before.  ...

Mike:   I am sorry that I just saw this message...problems were solved by replacing the console. The wireless receiver apparently wasn't the issue.

My notifications started working again....

I am not at my Mac right now, but I think all I did was download Growl for the Mac ($3.99) and then created a Pushover account (Pushover.net) and downloaded it to my iPhone. I installed the Growl plug-in from the Pushover.net website. There is a code that you are given that you need to enter...

Same problem here. Thanks for the Growl/Pushover suggestion. Works well and hopefully will continue to do so.

What is the best way to selectively turn a text notification on and off remotely for a single zone or group of zones. I have my system setup to text me if a door or window is opened, but I'd like to be able to turn notifications on my front door for a period of time, for example. I know I could...

My apologies for the delay in following up on this...the solution was to replace the console.  No more random events or random console beeps disabling.

I "resolved" my issues by removing my wireless receiver. I tried this since it connects to the A/B bus of the controller, the same as the console. Not a great solution because I can't use my wireless key fobs or sensors right now. Going to be replacing my receiver to see if it was the issue.

Thank you for the info. I have only one console.  Message is displayed on the console only.  I did contact Leviton and they said it is likely a "grounding" problem since I am getting random messages on the console.  I made sure all connections on the board were secure.  I've upgraded to 3.15...

New to the forum.  Here is my setup.   Omni LTe, FW 3.14a Console: 33A00-1 Wireless Receiver: 45A00-1 Wired Door/window sensors 4 relay module: 10A07-1 - wired to garage door ZigBee Interface Module: 81A00-3WHZB - for Kwikset Zigbee lock Wired smoke detectors ​Wired glass break detector Wired...