Search results

The System Sensor CO cell has an expiration date. They are good for about six yrs. I was surprised to find the Fire & smoke base unit has an expiration date. I thought Fire/smoke did not have expiration dates but this one does. Thoughts?

What is everyone using for Serial Communicator for M1G since the sunset for 3G is here? I have to replace my Uplink CDMAEZ since it will no communicating.   Thanks for feedback.

Hello - I had XEP running on AOL account for a while. It has stopped working for a bit. Has anything changed on Elk side or AOL. I have tried yahoo and still does not work. I have tried different port no's. I tried gmail and it blocked the Elk XEP because it doesn't meet gmail's security...

I have few Bosch Blueline Gen 2 Tritech motion detectors in the house. One in particular is giving false alarms whether its day or night in the living room. It has been going on for a bit. I have replaced it with a spare new one I had. I have even vacuumed around it thinking may be the spiders...

I have set up where the garage door closes automatically after 5min once the Area is Armed. However the garage door closes even when the Area is not Armed. What am I missing here?   Whenever the Area 1 is Armed (Also tried ARMED AWAY) THEN Set Garage Dr (Counter 9) to 300 WHENEVER Every 1 sec...

Wondering if any one is using a Uplink LTE30EX LTE Communicator with ELK M1G? My Uplink 4500EZ is dead after Uplink did a system wide update. It no longer functions. I need to replace it and wondering if LTE30EX is the right choice. I believe the 4G will be sunset in 2021.    It should connect...

Wondering if Uplink CDMAEZ will work with M1G? Does it work the same way as 4500EZ? Any issues?   Uplink performed a system wide upgrade at the end of January which resulted in GSM with serial # starting with 100 or 101 cease to communicate. Solution is to replace the unit.   I am getting a...

So one of the System Sensor Cosmo 2W near kitchen goes into Alarm mode for Carbon Monoxide. The blue light on the Cosmo 2W was flashing. I turned the M1G off/on and still kept going on. I swapped with another Cosmo 2W and it followed the cosmo 2w. I wasn't sure if there was CO presence and to be...

Apparently the XEP has not been communicating with the USA Central Station since the Alarm co changed services from Affiliated Monitoring. Uplink 4500EZ works fine. Apparently I was told they use Surgaurd 5 for receiver. Did not have any issues with Affiliated monitoring.   Does M1XEP...

Hello,   Wondering what others are using for DDNS. I was using changeip.com and it stopped working. I then switched to no-ip.com and still no. Just wondering what free DDNS works or any others.   Thanks

I have two rules for ELK-9100 relay. One to turn output 13 to ON which turn power off to the well when house is armed in Away mode. Another one if there is any water alarm to turn output 13 ON which should kill the power to the well pump.The water alarm rule  to shut off ELK-9100 for some reason...

This what I saw in my CS history. What does it mean? Must be XEP..... Thanks

Looking for a contact for a Shed door. I have two 3x8 bifold wood doors that needs to be wired. Looking for wired option only.   Thanks

Is there any way for Nest or Ecobee3 to work with M1G? I am thinking may be with an IFTTT reciepe? Not sure... Just thinking out loud.  I would be nterested if its possible to set it Away when Armed and so forth...

Is there any way for Nest or Ecobee3 to work with M1G? I am thinking may be with an IFTTT reciepe? Not sure... Just thinking out loud.  I would be nterested if its possible to set it Away when Armed and so forth...

Wondering the reliability of Resolution Products RE206Tilt Sensor. Wondering if anybody here has used them? Will it work with ELK/Honeywell setup?

Just like the title says. Looking for any feedback. Panel is somewhat new.   http://qolsys.com/ Thx

What is the best thermostate recommended with the elk system? Any suggetstions...   thx

Just wondering what is the actual draw on XEP. I have got a PD9 with a 12v 6A power supply feeding it. I wanted to feed XEP from PD9. However the current is limited to 250mA.on each output of the PD9. The XEP specs the draw at approx 300mA. I measured the current draw and it comes up at 90mA...

Checking to see if anybody has installed a System Sensor cosmod 2W and Cosmo 2w with m1g. I am looking to install along with 2WTAB. Looking for any info that would be helpfull.   Thanks